The treatment care is dependent on the type of timber used and the finish. This basic guide will help your custom piece last more than a lifetime.
Common Wood Types
When new and unfinished, oak furniture will naturally appear quite light with a slightly yellowed hue. All woods however can have significant colour variation from one piece to another, as with any natural product. Any sample products should be taken as indicative of the wood and finish, however it is not possible to guarantee an exact colour match.
Over time, sunlight will cause the wood to darken and mellow throughout its life. Oils in the skin will accelerate this process with any areas that are regularly touched, such as handles, table edges or chair backs, gaining a noticeably darker tint to the rest of the furniture.
Solid oak furniture may also be subject to rough grain protruding from previously smooth surfaces. This is usually caused in humid conditions or areas where spillage has occurred, the water having been absorbed into the wood causing the grain to swell.
Compared to oak, walnut is quite dark when first cut, especially the American black walnut varieties. Sunlight will cause walnut to lighten overtime, often bleaching into a light brown, with perhaps a slightly red tint to it.
In all other respects, walnut behaves much in the same way as oak (see above).
Ash behaves in all respects nearly identically to oak, the main difference is ash has a slightly narrower grain. Again, as with oak, ash will darken over time.
Cherry is a wood that starts very pale, and can look very similar to both ash and oak when young. Over time, sunlight will cause cherry to darken and redden.
Avoid placing objects on cherry for a long period of time in a fixed position as this will mean the area which has been covered will remain lighter than the rest of the wood.
Sourced from North America, grey elm has a rich grain that makes it a fascinating and beautiful timber, especially when used for inlays. Elm is hard wearing with lacquered finishes naturally darkening over time.
Stained versions of the woods described above, usually in ash or oak, adding a little more protection from spillages. Staining also adds a greater level of colour control between timber batches.
Finish: unless otherwise specified, our wood is usually finished in a durable clear matt lacquer. This provides an easy to care for durable finish that doesn't compromise the natural beauty of the wood grain.
Care: solid woods may expand and shrink with differences in temperature and humidity. Take care not to place your furniture next to radiators or anywhere subject to excessive changes in temperature or moisture content. We recommend that all kitchenware and beverages should be placed on mats and any spillages should be wiped away immediately.
Cleaning: to clean, wipe with a damp cloth before buffing with a dry cloth. In the event of more stubborn marks, a solution of mild detergent should be used on the cloth. Silicone based polishes should not be used on the wood as they will build up and leave a sticky residue on the surface.
Heat: never place hot items such as dishes directly onto the table without using a heat resistant mat or trivet as direct heat will draw out the moisture in the wood leaving a ring mark ingrained into the wood.
Oiled Wood Care
Finish: applied by hand. the pre-oilded finish enhances the open grained appearance of the wood giving it a slightly more rustic,matt finish. We use an Eco friendly Linseed based oil.
Care: despite having already been pre-oiled, we recommend that you apply an additional two coats of oil within 48 hours of taking delivery of the table. We would also recommend that you oil the table surface on a six month to yearly basis depending on its usage. Take care not to over-oil the table. We will give more advise during the wood selection process.
Please note that unless specified by a client, we manufacture entirely out of solid wood and it should always be remembered that the wood should not be exposed directly to excessive heat or moisture. For instance, do not place immediately adjacent to radiators and in the event of any spillages, wipe up all liquids as soon as possible before the liquid has the opportunity to soak into the wood. Again we will advise which woods to use dependent on site visit.
Cleaning: to clean, simply wipe down with a soft, barely damp cloth to remove any dust. In the case of stubborn marks, a solution of mild detergent such as washing up liquid should be used on the cloth. Avoid the use of scourers or bleaches. In the event of severe spillages and stains the surface can be re-finished. However it is recommended that you consult our customer services department.
All the woods we use is responsibly sourced natural timbers.
Finishes such as oils or lacquers also adhere to strict European Union guidelines and regulations, minimising their environmental impact.